Kia Airbag Module Download

SUMMARY: Kia Motors America is recalling certain model year 2016 Kia Optima vehicles manufactured November 10, 2015, to February 12, 2016. In these vehicles, a chemical enhancer required for the for the second stage deployment of the driver's frontal air bag was not loaded, resulting in the second stage not deploying in necessitating crashes. Kia Sorento: Airbag Module Second Generation XM (2011-2019) / Kia Sorento XM 2011-2019 Service Manual / Restraint / Airbag Module Driver Airbag (DAB) Module and Clock Spring Description. Automobile “Black Box” Data Download and Analysis of Passenger Car Airbag Module Data It is well known that the implementation of airbags in passenger cars and trucks has saved numerous lives and dramatically reduced injuries associated with motor vehicles accidents. Kia Sorento: SRS Control Module (SRSCM) Variant coding. / Kia Sorento XM 2011-2019 Service Manual / Restraint / SRSCM / SRS Control Module (SRSCM) Variant coding. After replacing the SRSCM with a new one, MUST perform the “Variant Coding” procedure. On SRSCM variant coding mode, the airbag warning lamp is periodically blinking (ON: 0.

How-to: Kia Soul 2016 2015 2014 Airbag Module Reset via OBD CAN Lines.

We offer a full selection of genuine Kia Sportage Air Bag Control Modules, engineered specifically to restore factory performance. Please narrow the SRS Airbag Module results by selecting the vehicle.

Kia airbag control unit MOBIS 95910-B2010

Remove crash data from KIA Soul on the table via OBD cable using CAN Low andCAN High pins. No need to open unit up, no soldering. Or directly in the car no need to remove the module.

Device to reset: Using Diatronik SRS+DASH+CALC+EPS or CalkMasterX OBD tool (they are the same).

After connect device with module/vehicle, go to Diatronik software

Select SRS Tool->Kia->Kia MOBIS EEPROM CAN BUS

Read ID okay

Select eeprom 25256

Kia Airbag Warranty

Read DTC

There are fault code stored.

Perform EEPROM reading

Diatronik OBD Tool read eeprom success

Disconnect power for 10 seconds

Select Crash Reset

Erase DTC

Done.

Airbag

Who Viewed This Article Also Views:

Special tool required
Deployment tool 0957A-34100A
Before scrapping any airbags or side airbags (including those in a whole vehicle to be scrapped), the airbags or side airbags must be deployed. If the vehicle is still within the warranty period, before deploying the airbags or side airbags, the Technical Manager must give approval and/or special instruction. Only after the airbags or side airbags have been deployed (as the result of vehicle collision, for example), can they be scrapped. If the airbags or side airbags appear intact (not deployed), treat them with extreme caution. Follow this procedure.
If an SRS equipped vehicle is to be entirely scrapped, its airbags or side airbags should be deployed while still in the vehicle. The airbags or side airbags should not be considered as salvageable parts and should never be installed in another vehicle.
1.
Turn the ignition switch OFF, and disconnect the battery negative cable and wait at least three minutes.

Used Airbag Modules

2.
Confirm that each airbag or side airbag is securely mounted.
3.
Confirm that the special tool is functioning properly by following the check procedure.
(1)
A.
Remove the driver’s airbag and install the SST (0957A-3Q100).
B.
Install the driver’s airbag on the steering wheel.
(2)
A.
Remove the glove box, and then disconnect the 2P connector between the front passenger’s airbag and SRS main harness.
B.
(3)
Side Airbag :
A.
Disconnect the 2P connector between the side airbag and side wire harness.
B.
(4)
Curtain Airbag :
A.
Disconnect the 2P connector between the curtain airbag and wire harness.
B.
(5)
Seat Belt Pretensioner :
A.
Disconnect the 2P connector from the seat belt pretensioner.
B.
(6)
Emergency Fastening Device :
A.
Disconnect the 2P connector from the emergency fastening device.
B.
4.
Place the deployment tool at least thirty feet (10meters) away from the airbag.
5.

Airbag Module Reset Software Download

6.
Push the tool’s deployment switch. The airbag should deploy (deployment is both highly audible and visible: a loud noise and rapid inflation of the bag, followed by slow deflection)
7.
Dispose of the complete airbag. No part of it can be reused. Place it in a sturdy plastic bag and seal it securely.
If an intact airbag has been removed from a scrapped vehicle, or has been found defective or damage during transit, storage or service, it should be deployed as follows:
1.
Confirm that the special is functioning properly by following the check procedure on this page.
2.
Position the airbag face up, outdoors on flat ground at least thirty feet (10meters) from any obstacles or people.
1.
If installed in a vehicle, follow the removal procedure of driver’s airbag front passenger’s and side airbag.
2.
In all cases, make a short circuit by twisting together the two airbag inflator wires.
3.
Package the airbag in exactly the same packing that the new replacement part come in.
Curtain Airbag (CAB) Module. Installation
1. Remove the ignition key from the vehicle. 2. Disconnect the battery negative cable and wait for at least thirty seconds. ...

2012 Kia Airbag Module Download Software

See also:

Transaxle Oil Temperature Sensor. Removal
1. Change the shift lever to 'N' range. 2. Remove the valve body assembly. (Refer to Hydraulic System - 'Valve Body&quo ...

Kia Airbag Light On

Front Seat Cushion Cover Component Location
1. Front seat cushion cover ...

Airbag Modules For Sale

Seat belts - Front passenger and rear seat 3-point system with combination locking retractor
To fasten your seat belt: Combination retractor type seat belts are installed in the rear seat positions to help accommodate the installation of child restraint systems. Although a combination re ...